How to Removal and installation of bock compressor parts - shaft seals from GEA Bock FK40 Compressor?

Why Need to Install And Removal the Shaft Seal of Bock Fk40 Compressor

Bock shaft seal is the key part of Bock FK 40 / 50 Compressor spare parts in the bus air conditioning system parts. When you repair your bock FK40 compressor or its oil leakage, maybe you need replace your Bock FK 40 Compressor Parts shaft seals 80023, While how to removal and install the bus A/C parts - bock FK shaft seals 80023, VehicleACParts will tell you today!

 

How to Installation Bock FK 40 Compressor Parts shaft seals 80023:

Work with utmost cleanliness.
Always replace the shaft seals complete Shaft seal (Part No. 80023), never individual parts thereof. So please make sure Do not use used BOCK shaft seals parts.
Prior to installation, check the sliding and sealing surfaces for cleanliness and damages.
Apply a thin film of oil on the sealing surfaces of the sliding ring (4), shaft seal cover (6), O-ring (3) and the Bock FK40 compressor shaft (use compressor oil).
Assemble the sliding ring (4), O-ring (3) and the guide ring (2) together as a unit. The large 
chamfer on the sliding ring (4) should show in the direction of the shaft seal cover (6).
During the assembly the compression spring (1) must engage audibly in the drive slot of the Bock FK Compressor Crankshaft and of the guide ring (2).
Install the shaft seal cover gasket (5) dry, don‘t impregnate it with oil.
Install the shaft seal cover (6) with the inscription „TOP“ upwards. Tighten the fixing screws 
(7) evenly, crosswise tightening torque = 37 Nm.
After installing the shaft seal, turn the Bock FK40 compressor shaft a few turns by hand and then carry out the leak test.
Install the leak oil collection ring (see section on leak oil collection ring
Insert the Woodruff key into the seat at the Bock FK40 compressor shaft end.
Mount the Bock FK40 Compressor drive/clutch.




 

How to Removal Bock FK Compressor Parts shaft seals 80023 From GEA BOCK compressor:

Dismount the bock FK40 compressor drive/magnetic clutch from the compressor.
Remove the Bock FK 40 Compressor Parts Woodruff key from seat at the shaft end.
Remove the leak oil collection ring (9) from the bearing flange
Unscrew the cylinder screwsand the felt inlay (8a or 8b, according to the type) 
Unscrew the screws (7) from the shaft seal cover (6).
Remove the gasket residues and the shaft seal cover gasket (5) from the bearing flange of Bock FK40 Compressor
Remove the shaft seal cover, the guide ring, the O-ring and the spring. (Watch out! The shaft seal cover is under spring tension! It may jump out by itself.)


Attention: The shaft seal cover (6) is under spring tension. The remaining oil may run out of the shaft seal chamber. Keep a suitable collection container ready

 

BUS A/C Parts - Bock FK Compressor Spare Parts Supplier - VehicleACParts 

As the best bus air conditioner parts supplier in China, VehicleACParts has been keenly focused on the after-sales service of bus air conditioner parts which supply original or replacement GEA bock FK 40/50 compressor parts,  BOCK FK 40/ FK50 compressor parts shaft seal 80023, BOCK FK 4/ FK40 / FKX40 Compressor Parts crankshaft 80154, BOCK FK 4/ FK40 / FKX40 Compressor Discharge and Suction Valve, 07130, 40460872 GEA BOCK FK40/470K Compressor Service Shut Off Valve 08082. FK40/560N Compressor valve plate; Bock FK40/650K Compressor valve plate, Flange Oval Repair gaskets for FKX26 Compressor Cylinder Heads, GEA bock FK40 K type whole gaskets Bock FK 40 470K compressor,  GEA Bock whole gaskets for BOCK FK50